Dns server is not responding
- 1 Fix: DNS Server not responding on Windows 10 – 2020 Updated
- 2 How to Fix ‘DNS Server is Not Responding’ Error in Windows
- 3 [Solved] DNS server is not responding on Windows 10
- 4 DNS-сервер не отвечает в Windows 10, 8, 7. Что делать и как исправить?
- 5 Fix
- 5.1 What is a DNS Server?
- 5.2 What Does DNS server not responding Mean?
- 5.3 How to Fix “The DNS server isn’t responding” in Windows 10 / 8 / 7
- 5.4 Method 1: Fix the DNS server isn’t responding Problem
- 5.5 Method 2: Reset DNS settings to Fix DNS server not responding
- 5.6 Method 3: Restart the Router
- 5.7 Method 4: Enter Safe Mode
- 5.8 Method 5: Disable All the Extra Internet Connections
- 5.9 Method 6: Troubleshoot Using a Software
- 5.10 Conclusion
Fix: DNS Server not responding on Windows 10 – 2020 Updated
Suddenly you cannot access any websites through the Internet. Then you try to troubleshoot the network problems on your Windows. It tells you the DNS server not responding is the culprit. You may see one of these:
“The DNS server isn’t responding.
Your computer appears to be correctly configured, but the device or resource (DNS server) is not responding.”
Don’t worry if this problem occurs. You can fix this problem with our following guide.
Try these fixes
If you’d to know why you can’t browse the Internet due to the ‘DNS server not responding, you can go to read the reason part. Otherwise, follow along with the solutions directly.
Bonus Tip: Try using VPN to fix the connection problem.
Note: The screens shown below are from Windows 10, but all the methods also apply to Windows 7/8.
First, let’s figure out what a DNS server is. DNS (Domain Name System) server helps to translate the website address into the IP address for your browser to connect to.For example, when you want to access our website: www.drivereasy.com on Chrome, the DNS server translates it into our public IP address: 220.127.116.11 for Chrome to connect to.
So you may know if there’s any wrong with your DNS server, you cannot access any website on your browser. No exception that if your DNS server stops responding, you cannot access the websites through the Internet.
Solution 1: Correct your DNS server address
The DNS server not responding error could be probably caused by an incorrect DNS server address. So you can follow these to correct your DNS server address:
1) On your keyboard, press the Windows logo key and R at the same time to invoke the Run box.
2) Type control and press Enter.
3) Click Network and Sharing Center in Large icons.
4) Click Change adapter settings.
5) Right-click on Local Area Connection, Ethernet or Wi-Fi according to your Windows. Then click Properties.|
6) Click Internet Protocol Version 4(TCP/IPv4), then Properties.
7) Tick on Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK.
8) Click Internet Protocol Version 6(TCP/IPv6), then Properties.9) Tick on Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK.
Restart your computer and try to access the website you want to go to again and see if it succeeds.
1) Type cmd in the search box from the Start menu. Then right-click on Command Prompt to select Run as administrator.
Note: Click Yes when prompted by the User Account Control.
2) On the open black window, type the following commands and press Enter after each. ipconfig /flushdns
Then restart your computer and try to access the website you want to visit again and see if it succeeds.
Your DNS server won’t respond if the network adapter driver is outdated. You can update your network adapter driver manually or, if you’re not confident playing around with drivers, you can do it automatically with Driver Easy.
Driver Easy will automatically recognize your system and find the correct drivers for it. You don’t need to know exactly what system your computer is running, you don’t need to risk downloading and installing the wrong driver, and you don’t need to worry about making a mistake when installing.
You can update your drivers automatically with either the FREE or the Pro version of Driver Easy. But with the Pro version it takes just 2 clicks (and you get full support and a 30-day money-back guarantee):
1) Download and install Driver Easy.2) Run Driver Easy and click the Scan Now button. Driver Easy will then scan your computer and detect any problem drivers.
3) Click Update All to automatically download and install the correct version of all the drivers that are missing or date on your system (this requires the Pro version – you’ll be prompted to upgrade when you click Update All).
Note: You can do it for free if you , but it’s partly manual.
After updating your network adapter driver, please restart your computer. Try to access the website you want to go to again and see if it succeeds.
Solution 4: Restart your modem and router
If your modem or router doesn’t work properly, the DNS server could stop responding, either. You can restart your modem and router if you have one to solve the problem.
1) Press the power button of your modem or router to power off, then wait for a while and press the power button again to start it again.
2) Try to access the website you want to go to again and see if it succeeds.
Hopefully, this article has helped you fixed the problem. Feel free to comment below with your own experiences and share with your friends or colleagues if they’re experiencing the same problem.
How to Fix ‘DNS Server is Not Responding’ Error in Windows
While trying to browse the internet you may have encountered the error that says, DNS Server is Not Responding. It may also show up with the websites name along with the message ‘Server DNS Address Could Not be Found.
’ Though it is not a very common problem but it occurs once in a while when the DNS server that translates a domain name doesn’t respond for any reason. But you can fix this problem easily by following the methods given below.
Before trying anything complex, let’s do some basic tasks to narrow down the problem. First of all, try to load the website in a different browser to see if it’s a browser related problem. You can clear the browser cache, cookies and then give it a shot as well.
You can also try to connect a second device a tablet or someone else’s laptop either wirelessly or wired to your network. Now try to browse that particular website and check if you still get the DNS Server Not Responding or DNS Server Unavailable error. If yes then follow the methods mentioned below to fix the problem.
Method 1 – Change The DNS Server Addresses
The DNS server address is usually obtained automatically, but you can set it to something more reliable.
As the DNS server your PC obtained automatically is not responding, you can change it to one of the most reliable DNS servers out there.
OpenDNS and Google DNS are considered to be the best and they are totally free. In our case we will use Google’s DNS server address. Let’s start off.
Windows 10 Users can simply type in ncpa.cpl into the Windows search box and press Enter. You can also Press on the Windows key from your keyboard and start typing which will take you to the search box.
Windows 7 users click on the Windows Key type in Run in the search bot and then type ncpa.cpl in the Run box and press Enter.
Now you will see the network connections and right click on the connection that you are using and click on Properties.
A new window will pop up, select Internet Protocol Version 4 (TCP/IPv4) and then click Properties again.In that window select the radio button that says Use the following DNS server Addresses. Then in the Preferred DNS Server field type in 18.104.22.168 and in the Alternate DNS Server field type in 22.214.171.124 then check Validate Settings Upon Exit box and click OK. Now restart your PC.
This will change the DNS servers on only the computer. If you are using internet on a mobile using a router then you can check out this post on how to change DNS servers on routers.
The DNS servers used above are Google DNS server addresses but you can also pick any other free DNS server from this list if you don’t want to use Google’s DNS server. Now try to connect to your internet and browse the websites that you were getting error to see if the problem is solved. If it didn’t, then try out method 2 which is flushing DNS.
Method 2 – Disable Unused Networks
Usually windows installs extra connections even if you never use them. But it’s best to have only the one connection that you use regularly and remove the other connections so that they can’t cause any kind of connection issue.
If there are any other connections that you are not currently using, then you need to disable them. To do that Press the Windows Key from your keyword and type in ncpa.cpl in the search box just we did in method 1. Windows 10 users have a round search icon right next to the Windows icon in the taskbar.
You can also find the network connections by navigating to Start >Control Panel >Network and Internet > Network and Sharing Center >Change Adapter Settings.
Now you will see all the connections that you are either using or not. Disable the connections that you are not using by right clicking on them and then clicking Disable.
In the picture above I’ve right clicked on the network that I’m using because the other ones are already disabled.
Windows and other operating systems usually store the DNS data in the cache This cache also store data of the visited websites and clearing the cache may solve the problem. To do that, click the Start button and type in cmd in the search box and press Enter from keyboard.
Command prompt will appear, then type in ipconfig /flushdns and hit Enter. This will remove all the DNS cache entry which just might resolve the problem. If not then also type in the following command and press Enter after each of them.
netsh winsock reset
Once done, restart your computer and check if the problem still exists.
Method 4 – Change Physical Address
At this point we will change the physical address of the computer. Go to Windows Start menu and type in cmd in the search box and hit Enter. In command prompt type in ipconfig /all and press Enter. Now find the physical address from there and write it down somewhere.
Now to go Start menu again and type in npca.cpl in the search box and hit Enter. This will show you the network connections. Now right click on the active connection that you are using and select Properties.Now click on Configure and then select Advanced tab.
After that click on Network address and select the radio button that says Values. Now type in the network address that you have written down previously. Make sure write them without the dashes this 408D5C44A795 and then click Ok and restart the computer.
Method 5 – Power Cycle Your Router and Computer
If you are using a router then unplug the router from the power source and as well as the computer. Leave them unplugged for at least 1 minute. This will clear the memory and release residual charge. Then plug them in again, turn them on and wait for them to fully start and connect. Now see if the problem is solved or not.
If you are using wireless network, you can also use an Ethernet cable to connect your PC directly to your router and check if you still get the error message. Now, if the problems is still there then move on to method 4 to try some other fixes.
Method 6 – Some Other Methods
If the three methods above doesn’t work for you then try some other methods listed below.
1. Uninstall Antivirus
Some people reported that after uninstalling their Antivirus program (mostly McAfee) the problem was gone. You may try some other good free Antivirus such as Avast or AVG.
2. Disable Your Firewall
Some people reported that after disabling their firewalls they problem was gone. This could be the solution for you too. Disable your firewall and check for the error.
3. Try Connecting in Safe Mode
Booting your computer in safe mood and trying to connect will help you determine if any third party software is causing the issue as the safe mode will only load the needed files for windows.
To do this reboot your computer and hold down the F8 key. Then select Safe mood with networking from the list of options.
Then test the connection and if you can connect, then probably any of the third party program is causing the issue a firewall or antivirus software.
The methods listed above are known to solve the DNS server not responding error that you get in your computer. If you still couldn’t solve the problem then comment below by mentioning which methods you tried and which you didn’t and I will try my best to help you out.
[Solved] DNS server is not responding on Windows 10
- Press Windows key + X and choose Command Prompt (Admin).
- When Command Prompt opens, enter ipconfig /all and press Enter.
- The list of information will now appear. Locate Physical Address and write it down.
- Close Command Prompt.
Now that you know your MAC address, you need to configure your network connection.
To do that, follow these steps:
- Open Network Connections window. Locate your connection and open its properties.
- When the Properties window opens, click on Configure.
- Go to Advanced tab and select Network Address from the Property list.
- Now select Value and enter the MAC address that you got from Command Prompt. Be sure not to enter any dashes while entering your MAC address.
- Click OK to save changes.
Users report that this solution works best after switching to Google DNS or OpenDNS, so be sure to try it.
Need to change your MAC address? It’s easier than you think with one of these MAC address changer tools!
3. Install the latest drivers
Your network adapter relies on drivers in order to work properly, and if you have any problems with it, it might be due to your drivers.
To fix DNS server errors on Windows 10, you need to visit your network adapter manufacturer’s website, download the latest drivers and install them on your PC.
If you can’t access the Internet at all, it might be caused by the DNS server not being unavailable, so download the drivers on a different device and install them on your PC.Some users are also recommending to uninstall your network drivers before installing the new drivers. To do that, follow these steps:
- Press Windows Key + X and choose Device Manager from the list.
- When Device Manager opens, locate your network adapter, right-click on it and choose Uninstall.
- The confirmation dialog window will now appear. If available, click on Delete driver software for this device and then click Uninstall.
- After you delete the driver, restart your PC.
- When your PC restarts, the default network driver will be installed. Check if the problem is resolved.
- If the issue still persists, install the latest drivers for your network device and check if that solves the issue.
Learn how to update your drivers a real technician with this complete guide!
Update drivers automatically
Downloading drivers manually can cause damage to your computer in case you downloaded the wrong version. We strongly suggest to do it automatically by using Tweakbit’s Driver Updater tool.
This tool is approved by Microsoft and Norton Antivirus. After several tests, our team concluded that this is the best automatic solution. Below you can find a quick guide how to do it.
- Download and install TweakBit Driver Updater
- Once installed, the program will start scanning your PC for outdated drivers automatically. Driver Updater will check your installed driver versions against its cloud database of the latest versions and recommend proper updates. All you need to do is wait for the scan to complete.Upon scan completion, you get a report on all problem drivers found on your PC. Review the list and see if you want to update each driver individually or all at once. To update one driver at a time, click the ‘Update driver’ link next to the driver name. Or simply click the ‘Update all’ button at the bottom to automatically install all recommended updates.
Note: Some drivers need to be installed in multiple steps so you will have to hit the ‘Update’ button several times until all of its components are installed.
Disclaimer: some functions of this tool are not free.
FAQ: Learn more about DNS servers
- What does changing your DNS to 8.8 8.8 do?
Changing your DNS to Google’s public DNS servers (126.96.36.199 and 188.8.131.52) can speed up your connection time to most websites. This means your computer will access websites faster. Keep in mind that does not improve your download speed when it comes to streaming or downloading large files.
- Is changing DNS dangerous?
Changing your DNS settings is not dangerous. This change won’t damage your computer or harm your network. This is a completely safe and reversible action and you can always go back to your previous settings if you’re not satisfied with the connection quality or speed.
DNS errors are usually caused by network and Internet issues on users’ end, incorrect DNS and DHCP settings, website outage or restrictions set in place by your ISP.
Editor’s Note: This article continues on the next page. If you want to read more about DNS settings on Windows 10, check out our collection of guides.
Still having issues? Fix them with this tool: This software will repair common computer errors, protect you from file loss, malware, hardware failure and optimize your PC for maximum performance. Fix PC issues and remove viruses now in 3 easy steps:
- Download this PC Repair Tool rated Great on TrustPilot.
com (download starts on this page)
- Click Start Scan to find Windows issues that could be causing PC problems.
- Click Repair All to fix issues with Patented Technologies (Exclusive Discount for our readers).
- Restoro has been downloaded by 0 readers this month.
Editor's Note: This article was originally published in November 2016 and was revamped and updated in November 2020 for freshness, accuracy, and comprehensiveness.
Few users reported that DNS servers may not be responding while using wireless networks. However, you can fix that simply by updating your router’s firmware. We have to warn you that this is an advanced process, so you need to be extra cautious in order to avoid causing damage.
Before updating your router’s firmware be sure to back up its settings. To see how to properly update the firmware, we advise you to check your instruction manual.
If your DNS server not responding on wifi/wireless, you may also want to check the channels you’re using.
6. Use netsh command
According to users, you can fix DNS failure simply by running few commands from Command Prompt. To do that, follow these steps:
- Open Command Prompt as administrator.
- When Command Prompt opens, enter:
- netsh int ip reset
- netsh winsock reset
- ipconfig /flushdns
- ipconfig /renew
- After all commands are executed, restart your computer.
By performing these commands you’ll reset your IP and clear the DNS cache, so be sure to try this method.
7. Restart your modem
One way to fix DNS server not responding error on Windows 10, is by restarting your modem. To do that, simply press the power button on your modem to turn it off.
Wait for 30 seconds and press the power button again to turn it on. Wait until the modem turns on completely and check if the problem still persists.
8. Start your PC in Safe Mode
Sometimes third-party applications such as antivirus or VPN tools can interfere with your Internet connection.
In order to fix DNS server not responding error on Windows 10, be sure to try accessing the Internet from Safe Mode.
If you’re not familiar, Safe Mode is a special mode in Windows that runs only with basic software and drivers. To enter Safe Mode on Windows 10, you need to follow these steps:
- Open the Start Menu and click the Power button. Hold down the Shift key on your keyboard and click Restart.
- You’ll see three options available. Choose Troubleshoot.
- Select Advanced options > Startup Settings and click the Restart button.
- When your PC restarts you’ll see a list of options available. Select Safe Mode with Networking by pressing F5 on the keyboard.
- Safe Mode will now start.
When Safe Mode starts, check if your network connection is working. If there are no problems with your Internet connection in Safe Mode it means that third-party software is interfering with your network connection.
To fix this issue, you need to find and remove the problematic application from your PC.
Editor’s Note: This article continues on the next page. If you want to read more on how to optimize your Internet connection, feel free to explore our collection of guides.
Editor's Note: This article was originally published in November 2016 and was revamped and updated in November 2020 for freshness, accuracy, and comprehensiveness.
DNS-сервер не отвечает в Windows 10, 8, 7. Что делать и как исправить?
Одной из самых частых ошибок связанных с подключением к интернету в Windows, является ошибка: “DNS-сервер не отвечает”. При этом, пропадает доступ к интернету.
На значке подключения скорее всего будет желтый треугольник, а в браузере, при попытке открыть сайт, вы скорее всего увидите ошибку “Не удается найти DNS-адрес”, “err name not resolved “, или что-то в этом роде. Проблема эта вызвана сбоем в работе DNS-сервера, который отвечает за перенаправленные IP-адреса на домен.
Если говорить о причинах возникновения этой ошибки, то виновником может быть как сам компьютер, так и маршрутизатор, или оборудование на стороне провайдера.
Сама ошибка “DNS-сервер не отвечает” появляется в результате диагностики сетей Windows. Запустить диагностику очень просто. Достаточно нажать правой кнопкой мыши на значок подключения к интернету, и выбрать “Диагностика неполадок”.
Иногда, может появляться ошибка: “Параметры компьютера настроены правильно, но устройство или ресурс (DNS-сервер) не отвечает”.
Вот такие ошибки. Если вы не знаете что делать, то сейчас мы рассмотрим несколько эффективных советов, которые должны помочь избавится от данных ошибок. В итоге, интернет на вашем компьютере заработает, и сайты начнут открываться. Решения будут одинаковыми для Windows 10, Windows 8, и Windows 7.
Как исправить ошибку “DNS-сервер не отвечает”?
Для начала, я советую выполнить несколько простых решений. Есть шанс, что они помогут, и вам не придется разбираться с более сложными настройками.
- Если у вас интернет подключен через роутер, или модем (по Wi-Fi, или по кабелю), и вы наблюдаете ошибку “DNS-сервер не отвечает”, то попробуйте просто перезагрузить роутер. Отключите питание роутера где-то на минуту, и включите обратно. Не важно какой у вас роутер, TP-Link, D-link, ASUS, или еще какой-то.
- Перезагрузите свой компьютер, или ноутбук. В данном случае не важно, интернет у вас идет через роутер, или кабелем напрямую от провайдера. Просто выполните перезагрузку.
- Если интернет подключен через роутер, то проверьте, работает ли интернет на других устройствах. Нет ли там ошибки с ответом DNS-сервера.
- При подключении через маршрутизатор, если есть возможность, можно подключить интернет напрямую к компьютеру. Для проверки.
- Постарайтесь вспомнить, после чего появилась ошибка DNS, и проблемы с доступом к интернету. Может после смены каких-то настроек, или установки программ.
Если эти советы не помогли, то попробуйте применить решения, о которых я напишу ниже.
Проверяем службу DNS-клиент
Прежде чем что-то менять, я рекомендую посмотреть, работает ли служба “DNS-клиент”. Нажмите на клавиатуре сочетание клавиш Win + R. В появившемся окне введите команду services.msc, и нажмите Ok.
В новом окне ищем службу “DNS-клиент”, нажимаем на нее правой кнопкой мыши, и выбираем “Свойства”.
Тип запуска должен быть “Автоматически”. И если у вас кнопка “Запустить” будет активной, то нажмите на нее. Дальше: “Применить” и “Ok”.
Если служба у вас была отключена, и вы ее включили, то после перезагрузки компьютера интернет должен заработать.
Меняем настройки DNS-серверов в свойствах подключения
Дальше мы проверим настройки DNS-серверов в свойствах подключения, через которое компьютер подключен к интернету. Если там прописаны какие-то адреса, то можно попробовать выставить автоматическое получение, либо прописать DNS-адреса от Google. Этот способ очень часто позволяет избавится от ошибки “DNS-сервер не отвечает”.
Нам нужно открыть окно со всеми подключениями. Для этого можно нажать правой кнопкой мыши на значок подключения к интернету, и выбрать “Центр управления сетями…”. Дальше переходим в “Изменение параметров адаптера”.
Дальше правой кнопкой мыши нажимаем на то подключение, через которое вы подключены к интернету (к роутеру), и выбираем “Свойства”. Если подключение по Wi-Fi, то это подключение “Беспроводная сеть”, если по кабелю, то “Ethernet” (Подключение по локальной сети).
У меня, например, проблема с DNS при подключении по Wi-Fi сети через роутер.
В новом окне выделите “IP версии 4 (TCP/IPv4)”, и нажмите “Свойства”. Если в новом окне у вас прописан какой-то DNS-сервер, то можно попробовать выставить автоматическое получение адресов, и проверить подключение к интернету после перезагрузки компьютера.
Но чаще всего помогает следующее: ставим переключатель возле “Использовать следующие адреса DNS-серверов”, и прописываем DNS от Google:
Нажимаем “Ok” и перезагружаем компьютер.
Такое решение помогает очень часто. Если у вас проблема с получение DNS на всех устройствах, которые подключены через один роутер, то эти адреса можно прописать в настройках роутера, тогда они будут применяться для всех устройств. Как правило, сделать это можно в настройках вашего роутера, в разделе “Интернет”, или “WAN”. Где задаются параметры для подключения к провайдеру.
Для примера, покажу как это сделать на роутере TP-Link:
Не забудьте сохранить настройки.
Очищаем кэш DNS и другие сетевые параметры
Нужно просто запустить командную строку, и по очереди выполнить несколько команд, которые выполнять очистку кэша DNS-адресов, и других сетевых настроек. Этот способ подойдет как для Windows 10, так и для Windows 7 (8).
Командную строку нужно запустить от имени администратора. Если у вас Windows 10, то просто нажмите правой кнопкой мыши на меню пуск, и выберите “Командная строка (администратор)”. В Windows 7, в поиске можно набрать “cmd”, нажать правой кнопкой на “cmd” в результатах поиска, и выбрать “Запустить от имени администратора”.
По очереди копируем и выполняем такие команды:
В Windows 10 можно еще попробовать выполнить сброс сетевых настроек. Это практически то же самое.
После этого перезагрузите компьютер.
Обновление: отключаем или удаляем антивирус Avast
The DNS server isn’t responding error is one of the most common DNS errors which you will experience while connecting to the internet in Windows operating systems.
The DNS server not responding error is extremely common and even if the internet connection settings are properly configured on your Windows computer there is a high possibility that you will still get this DNS server error The DNS server isn’t responding.
Fix “The DNS server isn’t responding” error in Windows 7/8/10
Today in this how-to-fix tutorial, we are going to tell everything about the DNS server error (what is a DNS Server and what does DNS server not responding mean?) and how to fix “The DNS server isn’t responding” error in Windows 10, 8, 7 operating system. Let’s see now.
What is a DNS Server?
DNS or Domain Name server is a technology which helps in the management of the public as well as domain names of all the websites. One can think of DNS as a phonebook where the phone numbers of a person are written right next to their name.
With the help of DNS, you just have to enter the URL address and your computer will detect the address automatically with the help of domain name server. You can also follow this DNS server guide to know in details about what is DNS server? Why you should change DNS Server address? How to change DNS server on Windows, Mac, and Android with the best public DNS servers? etc.
What Does DNS server not responding Mean?
Before we tell you how to fix DNS server not responding issue on your computer, let’s find out what does The DNS server isn’t responding mean.
The main reason that you are getting this error on your computer is because of the incorrect hosts file on your computer. If the host names inside the hosts file of your computer are having an outdated listing it will lead to DNS server not responding error and you won’t be able to connect with the internet.
Simply, you have to make changes to the hosts file manually as this will help you in configuring The DNS server isn’t responding problem. You can open the hosts file using notepad and then search for the website to which you are not able to connect. Delete that website and save your hosts file and you should open that website easily without any error.
How to Fix “The DNS server isn’t responding” in Windows 10 / 8 / 7
Now that you know what does DNS server not responding mean and also know the reason behind this DNS server error, let’s follow the methods which will help you in solving “The DNS server isn’t responding” in Windows 10, 8, and 7 computers. Here we go:
Method 1: Fix the DNS server isn’t responding Problem
Before you start following this method we suggest you to take backup of the router settings and the firmware. This will help you in case anything goes wrong and you can restore back to the settings.
Step (1): You have to change DNS server manually. For changing the DNS server, open Control panel on your computer and then select Network and Internet. Once you have opened Network and Internet settings, you have to choose Network Sharing Center. Here you have to select Change Adapter settings.
Step (2): You will find all the adapters which are installed on your computer. Now you have to select the adapter which you are using on your computer. Right click on the adapter and then select Properties.
Step (3): You will see many options here. Select Internet Protocol Version 4 (TCP/IPv4) from here and then click on Properties option.
Step (4): Change the DNS server by selecting “Use the following DNs server addresses” option.
Step (5): Enter the below-mentioned DNS addresses in their respective fields:
Preferred DNS Address – 67.222.222Alternate DNS Address – 67.220.220
Or, you can also use Google’s DNS address:
Preferred DNS server: 184.108.40.206Alternate DNS server 220.127.116.11
Step (6): Once you have entered the details, select Validate settings upon exit. Select OK and then click on exit button.
Once you have changed the settings in the adapter, now you need to make changes in the router configuration as well as it will help you to fix the DNS server isn’t responding problem.
Step (1): Download and install OpenDNS on your computer. You can download it from this link.
Step (2): Open command prompt on your computer and then enter IPCONFIG/ALL
Step (3): Find the LAN or Local Area Adapter here. Now write down the Physical address which you see in the command prompt.
Step (4): Now, open Start menu and then enter CPL.
Step (5): Select the Network Adapter and right click on it. Now select Properties from the menu displayed.
Step (6): Select Configure and then open Advance tab and open Network address.
Step (7): From here you have to choose redial button Value. Here you have to enter the physical address which you have written down before from the command window.
For the example: If the Physical address of your network adapter is 78-DD-08-F1-DF-B0 then you have to remove the dashes and type it as 78DD08F1D0).
Step (8): Finally, select OK button and then choose Reboot the system.
Once you have done all the above-mentioned things, search for the drivers of the network adapter from the manufacturer’s website. This should fix the DNS server is not responding error. If your connection is blocked then you can disable the Network Firewall settings.
Method 2: Reset DNS settings to Fix DNS server not responding
You can also reset the DNS settings as it will help to fix DNS server isn’t responding issue very quickly. Here’s how to reset DNS settings in Windows system:
Step (1): First of all, open Run window on your computer by pressing Windows + R key. Enter cmd in the dialog box to open the command prompt window.
Step (2): Now to reset the DNS settings, you have to execute the commands which we have mentioned below:
ipconfig /flushdns > Hit Enteripconfig /registerdns > Hit Enteripconfig /release > Hit Enteripconfig /renew > Hit Enternetsh winsock reset > Hit Enter
Once you have executed all these commands successfully, reboot your system and DNS server isn’t responding error should be resolved.
Method 3: Restart the Router
The above two methods should solve the DNS server is not responding error, however if you failed to fix the issue you can disconnect the Wi-Fi router and reboot it. Rebooting the router has helped a lot of people and it is really a quick fix. Make sure that you have switched off the router for at least 2 minutes before you turn it back on.
The 2-minute time interval will make sure that all the memory is erased along with the remaining charge. Provide the power supply to your router after 2 minutes and this should fix “The DNS server isn’t responding” in Windows 10 / 8 / 7 computer.
You might also to know: How to Set Bandwidth Limit on TP-Link Router
Method 4: Enter Safe Mode
If you are still experiencing the problem then you can enter the safe mode of your computer as it has proven as DNS server not responding fix. You might have installed a third party software which disabled the internet connection on your computer.
To enter Safe mode on your computer, simply power it off and hold the F8 key when it is booting. Once booted, try to connect with the internet. Learn: How to Open Windows 10 in Safe Mode [Quick ways]
Method 5: Disable All the Extra Internet Connections
If you are using a lot of Internet connections on your computer then also you can experience this error. Windows also install a lot of connections by default when you connect to a new network.
To uninstall all the extra connections which you are not using on your computer, you have to open Control Panel and then go to Network and Sharing. Select Change adapter settings option and then select the connection which you are not using. Right click on the extra connection and then choose Disable option.
You might also to see: How to Disable Internet Connection Sharing in Windows
Method 6: Troubleshoot Using a Software
If the above explained all methods failed for you then you can take help of a software to troubleshoot the DNS server is not responding problem.
Smart Dns Server Not Responding Fixer is a tool which specializes in fixing the Windows registry errors and all the DNS server issues.
You can easily install the software called Smart Dns Server Not Responding FixerPro on your computer and start the Scan.Once the scan is completed, it will display all the problems which were identified in the scan and which need to be fixed.
In order to fix the DNS server not responding issue, you can click on the Fix button which will resolve all the DNS errors which you are having on your computer.
You can perfectly use this software in Windows 10, 8, 8.1 and 7 operating system. To see what was scanned and what were the issues you can check the logs of the software.
So, these are the top 6 most helpful methods which make to our guide of how to fix DNS server not responding issue. We hope that the DNS error which you were facing on your computer is resolved after following this guide “how to fix The DNS server isn’t responding in Windows 10 / 8 / 7” and now you are able to connect to the internet.
This is not a really big issue but a very common one and the solution to this issue is also quite simple as you have already seen above. However, if you are not able to fix DNS server is not responding error with simple solutions then you have to opt the advanced methods.
Feel free to let us know using the comments section below – which method worked best for you as the DNS server not responding fix?